Korean rolled aluminum for international buyers
Coil, sheet, plate, and foil from qualified Korean mills, produced to the buyer’s specification, with one counterparty managing the mill, the qualification, the documents, and the shipment.
What Korean mills roll, and for whom
A compact flat-rolled industry: a few integrated mills plus re-rollers and foil mills, exporting a meaningful share of output.
Korea has a compact flat-rolled aluminum industry built around a small number of integrated mills that cast, hot roll, cold roll, and finish, plus a layer of re-rollers and foil mills that buy coil and roll it thinner. The product range covers the common wrought families from commercially pure 1xxx through the manganese, magnesium, and iron-silicon families that packaging, transport, and battery customers specify. Since the 2025 and 2026 changes to US tariffs, more of that output is available to buyers in Asia, the Middle East, Europe, and the Americas outside the US.
Inquivix Technologies sources flat-rolled aluminum from qualified Korean mills for international buyers who have a defined product specification and want one counterparty managing the mill relationship, the qualification, the documentation, and the shipment. We do not roll aluminum. We do not hold stock. Every order is produced to the buyer's specification by the mill best suited to it.
Forms: coil, sheet, plate, foil
Defined by thickness and by how the product is delivered. Name the form explicitly in a specification.
- Coil is the mill's primary output: continuous strip wound on a core, in thicknesses from foil-stock gauges up to several millimetres, slit to the buyer's width. Most industrial buyers take coil because it feeds their own lines directly.
- Sheet is coil cut to length, delivered flat in packs. Conventionally, sheet is flat-rolled product from 0.2 mm up to 6 mm thick. Sheet is specified when the buyer's process starts from blanks rather than strip.
- Plate is flat-rolled product over 6 mm thick, delivered flat, often with a machined or sawn edge and a flatness tolerance tighter than sheet. Plate is a 5xxx and 6xxx product in practice.
- Foil is flat-rolled product below 0.2 mm, usually far below it, wound on a core. Foil mills work from foil stock coil supplied by the integrated mills. Packaging foil, pharmaceutical blister, and battery current collector foil are the main markets.
The thickness boundaries above are the EN convention (EN 485 and EN 546). ASTM draws the lines at 0.15 mm (0.006 in) and 6.3 mm (0.250 in). Korean mills quote to whichever standard the order names, so state the standard with the thickness.
Alloy families available from Korea: 1050, 3003, 5052, 6061, 8011
Composition limits for every alloy named here are on the alloy reference page.
1xxx: commercially pure aluminum
1050, 1070, and 1100 are 99.5 percent or purer aluminum with no deliberate alloying. They are soft, highly formable, corrosion resistant, and the best electrical and thermal conductors of the wrought families. They are not strong. Typical products are electrical busbar and foil, chemical and food equipment sheet, heat exchanger fin stock, lithographic sheet, and household foil. In foil gauges, 1xxx (mainly 1235) serves electrical, battery current collector, and some converter foil; packaging and pharmaceutical foil is mostly 8xxx, covered below.
3xxx: manganese alloys
3003 is the general-purpose alloy of the family: moderate strength, excellent formability and weldability, good corrosion resistance. 3004, 3104, and 3105 add magnesium for higher strength. 3004 and 3104 are the alloys of beverage can body stock and are rolled to tight gauge and earing tolerances on dedicated lines. 3003 and 3105 serve roofing and cladding, heat exchanger tube and fin, cooking equipment, and general sheet metal work.
5xxx: magnesium alloys
5052, 5083, and 5182 are the most widely traded members of the 5xxx family, the strongest non-heat-treatable wrought alloys, with strength rising with magnesium content. 5052 is the workhorse for formed and welded sheet parts, fuel tanks, truck and trailer bodies, and marine fittings. 5083 is the marine and pressure vessel alloy, supplied as plate for hulls, tanks, and cryogenic service. 5182 is the beverage can end alloy and is also used in automotive inner panels. All three are supplied in strain-hardened tempers and are not heat treatable.
6xxx: magnesium-silicon alloys
6061 and 6063 are heat-treatable alloys, supplied from Korea mainly as plate and as extrusion billet rather than as coil (6xxx automotive body sheet is a separate coil product and is specified by grade on enquiry). 6061 plate is the structural and machining alloy for jigs, fixtures, tooling plate, and transport structures. 6063 is primarily an extrusion alloy; it appears here because Korean mills cast 6063 and 6061 billet for extruders, and some international buyers source billet and plate from the same mill. Billet is covered on the primary metal page.
8xxx: iron-silicon foil alloys
8011, 8021, and 8079 are the foil alloys. Their iron and silicon content gives higher strength and better pinhole resistance at very thin gauges than 1xxx foil. 8011 is the general packaging and closure foil. 8079 is used for thin flexible packaging and for pharmaceutical blister. 8021 is the thicker, higher-strength foil for blister lidding and semi-rigid containers. Battery cathode current collector foil is rolled from 1xxx alloys, typically 1060 or 1070 class, to gauges in the low tens of micrometres; it is a specialised product with its own surface cleanliness and tensile requirements.
Tempers
Temper describes the mechanical condition the mill delivers. It is as important as alloy in a specification.
- O is fully annealed: softest, most formable, lowest strength.
- H1x is strain hardened only. H12, H14, H16, H18 indicate quarter, half, three-quarter, and full hard.
- H2x is strain hardened and partially annealed. H22, H24, H26 have similar strength to the H1x equivalent with better ductility.
- H3x is strain hardened and stabilised, used for magnesium-bearing 5xxx alloys to prevent age softening. H32, H34, H36, H38 are the usual transport, tank, and formed-part tempers; can end stock (5182) is supplied H19 or H48.
- T4, T6, T651 apply to heat-treatable 6xxx: solution treated and naturally aged (T4), artificially aged (T6), and stress relieved by stretching (T651), the last being the standard plate temper.
Korean mills produce the full range for the alloys they roll. A buyer specifying a temper should also state the standard against which the mechanical properties will be tested, since minimum values differ slightly between KS, ASTM, EN, and JIS for the same nominal temper.
Standards Korean mills certify to
KS by default. ASTM, EN, and JIS routinely on request. Name the standard at inquiry.
Korean mills work to the Korean Industrial Standards (KS) by default. The sheet, plate, and strip standard is KS D 6701, which is closely aligned with the corresponding JIS standard. On request, and routinely for export, mills certify to:
- ASTM B209/B209M for sheet and plate and ASTM B479 for foil
- EN 485 (sheet, strip, and plate: mechanical properties and tolerances) with chemical composition to EN 573 and foil to EN 546
- JIS H4000 for sheet, plate, and strip and JIS H4160 for foil
The mill test certificate states the standard tested against, the alloy and temper, the chemical analysis of the cast, and the mechanical test results for the lot. A certificate issued to KS cannot be converted to ASTM after the fact.
Dimensions, surface, and packaging
Capability differs by mill and product line. We confirm the available range for each inquiry rather than publish a table that is wrong for some combination.
- Thickness and tolerance, and whether the tolerance is to the standard or tighter
- Width and slitting requirement, including edge condition (mill edge or slit edge)
- Coil inner diameter, maximum outer diameter, and maximum coil weight, matched to the buyer's uncoiler
- For sheet and plate, length, flatness requirement, and pack weight
- Surface: mill finish, degreased, bright, or with a specified roughness; any requirement for a chromate-free pretreatment or a lacquer
- Packaging: eye-to-sky or eye-to-wall, interleaving paper, moisture protection, and whether the destination requires fumigated or heat-treated pallets
Application clusters
Packaging
Can body stock (3004, 3104), can end stock (5182), foil stock and finished foil (1xxx, 8xxx), closures and semi-rigid containers (8011, 8021). The tightest gauge and earing tolerances in the industry; mills that serve this market run dedicated lines and qualify customers over trial campaigns.
Battery materials
Cathode current collector foil (1xxx), battery can and module sheet (3xxx), and cell casing material. Korean mills supply the domestic cell makers and their overseas plants. The foil is a specialised product with cleanliness, tensile, and elongation requirements beyond the general standards.
Automotive
Body and structural sheet (5xxx, and 6xxx where available), heat exchanger stock (3xxx), and trim. Automotive buyers qualify a mill through a formal PPAP-type process; the mill's existing automotive approvals shorten it.
General engineering
1xxx, 3xxx, and 5xxx sheet and plate for fabrication, signage, enclosures, transport, and construction. The broadest market and the one where a new international buyer most easily qualifies Korean supply.
How to specify an order
A complete specification lets the mill quote without a second round of questions and lets us match the inquiry to the right mill the first time.
Form
Coil, sheet, plate, or foil.
Alloy and temper
For example 3003 H14, 5052 H32, 8011 O.
Standard
KS, ASTM, EN, or JIS for chemistry and mechanical properties.
Dimensions
Thickness, width, and length or coil dimensions, with tolerances.
Surface and packaging
Finish, pretreatment, interleaving, pallet requirements.
Quantity
Per order and expected annual volume, which affects which mills will quote.
Application
Can stock, battery foil, and automotive sheet route to different lines.
Destination and Incoterm
Decides documentation and, for the US and EU, the tariff and CBAM treatment on the compliance page.
Required delivery date
Lead times run from the mill's rolling schedule, not from stock. We state the lead time as a range in every quotation.
Frequently asked questions
Can I buy a single coil to trial?
Usually yes for standard alloys and gauges, subject to the mill's minimum production quantity for that item. Trial quantities and pricing are agreed per inquiry.
Do Korean mills supply cut-to-length sheet or only coil?
Both. Sheet and plate are cut and packed at the mill. Foil is supplied by foil mills, which buy foil stock from the integrated mills.
Which standard should I specify?
The one your downstream process or your customer's drawing calls for. If none is specified, Korean mills certify to KS. ASTM, EN, and JIS certification are routine on request and should be named at inquiry.
Can the mill provide CBAM emissions data?
This is mill-specific and is confirmed at inquiry stage. See the compliance page for what EU buyers need.
What is the minimum order?
It depends on the mill, the alloy, and the width. We confirm it with the quotation.
Have a specification or a sourcing question? Tell us the product, alloy, quantity, and direction.
Discuss your requirement