Menu
Aluminum / Primary metal

Primary metal, alloys and scrap into Korea

Korea does not smelt primary aluminum. Every tonne its mills, extruders, foundries, and foil producers melt is imported. We source, qualify, document, and deliver it, with a Korean-speaking counterparty on the technical side.

Into Korea

Why Korean mills buy metal from overseas

No domestic primary smelting. A steady, specification-driven import market for ingot, billet, slab, alloying material, and scrap.

Korea does not smelt primary aluminum. Every tonne of primary metal that Korean rolling mills, extruders, foundries, and foil producers melt is imported, and so is most of the alloying material and a large share of the scrap. The country's aluminum industry is therefore a steady buyer of ingot, billet, slab, master alloys, and sorted scrap from smelters, remelters, and scrap processors overseas, and it buys to specification, on long-term and spot terms, with documentation checked before a lot is accepted.

Inquivix Technologies supplies metal, alloys, and scrap into Korea for producers that need a qualified overseas source and want a Korean-speaking counterparty on the commercial and technical side of the relationship. We are based in Incheon, the main import port for the Seoul and Gyeonggi industrial region. We do not smelt or remelt; we source, qualify, document, and deliver.

What we supply

Grades and forms below; composition limits on the alloy reference page.

Primary aluminum ingot (P1020, A7)

The standard trading grades are P1020 and, from CIS-origin smelters, A7. P1020 is aluminum of 99.70 percent minimum purity with silicon limited to 0.10 percent and iron to 0.20 percent; the designation reads P, then the silicon maximum, then the iron maximum, and the LME-deliverable form is written P1020A. A7 is the equivalent grade under the Russian GOST system, also 99.70 percent minimum. Both are supplied as standard ingot in bundled stacks, and both are what a rolling mill or extruder means when it specifies "primary." Higher-purity grades (P0610, P0506, and above) are available for electrical and specialty applications on request.

Extrusion billet

Billet is DC-cast log, homogenised and cut to length, in 6xxx alloys for extruders. 6063 is the architectural and general extrusion alloy; 6061 is the structural alloy; 6005 and 6082 are specified for higher-strength sections. Billet is specified by alloy, diameter, length, homogenisation condition, and surface, and is supplied with a cast analysis for each heat. Korean extruders buy billet from overseas casthouses when domestic supply is short, when a specific alloy or diameter is not available locally, or when price makes an imported source competitive after freight.

Rolling slab

Slab is DC-cast rectangular ingot for rolling mills that do not cast all their own input, or that need a specific alloy they do not cast. It is specified by alloy, dimensions, and surface condition (scalped or unscalped), and it is supplied with a cast analysis. Slab is a lower-volume, higher-specification item than ingot, and the qualification is correspondingly more detailed.

Master alloys and alloying elements

Mills and foundries adjust alloy chemistry in the furnace with master alloys and pure additions. We supply the common items:

  • Grain refiners, principally aluminum-titanium-boron rod and waffle (AlTi5B1 and related grades)
  • Hardeners: aluminum-silicon, aluminum-manganese, aluminum-magnesium, aluminum-copper, aluminum-iron, and aluminum-chromium master alloys in waffle or ingot
  • Pure alloying elements: magnesium ingot, silicon metal lumps, manganese flake or briquette, copper

Master alloys are supplied with a certificate of analysis per lot and, for grain refiners, with the producer's specification sheet.

Sorted aluminum scrap, including UBC

Scrap is the fastest-growing input for Korean mills and foundries because it lowers both cost and embedded emissions. We supply sorted scrap by alloy and grade, principally clean industrial process scrap (new scrap) and segregated alloy scrap, described by the ISRI specification the industry uses for trading. Scrap is supplied baled, briquetted, or loose depending on grade and the buyer's furnace, with moisture, contamination, and radioactivity checked before shipment. Which grades we handle at any time depends on what Korean buyers are seeking and what qualified sources can supply; the inquiry form asks for the grade. Segregated alloy scrap is offered by alloy, including 3003, 6061 and 6063. Used beverage can (UBC) scrap is sourced on request, subject to availability.

How a Korean mill qualifies a new metal source

A Korean rolling mill or foundry does not switch metal suppliers on price alone. The sequence is consistent across the industry even where details vary by mill.

  1. Specification review

    The mill issues its purchase specification for the item: alloy or purity grade, chemical limits (often tighter than the trading grade), form, dimensions, packaging, and documentation. The supplier confirms it can meet every line or states the exceptions.

  2. Certificate review

    The supplier provides a certificate of analysis for representative production, the producer's quality certifications, and, for scrap, the sorting and processing description. The mill's quality department reviews the chemistry against its internal limits.

  3. Sample

    A physical sample is sent for the mill's own spectrographic analysis. For ingot and billet the mill may also section the sample to check for inclusions, porosity, and surface condition.

  4. Trial lot

    A production-scale lot, typically one container or one furnace charge, is purchased and run. The mill records melt behaviour, dross, chemistry drift, and the quality of the rolled or extruded product. For scrap, the trial establishes the recovery rate, which drives the price the mill will pay.

  5. Approval and terms

    On a successful trial, the source is added to the approved supplier list, and commercial terms for regular supply are set: price basis (usually LME plus a premium), quantity, delivery schedule, payment, and the documentation set per shipment.

Our roleOn the supplier side: we assemble the documents in the format the mill expects, handle sample logistics, translate and interpret the mill's technical questions for the source, and manage corrective action if a trial lot falls outside specification. Korean-language technical communication with the mill is the part of the service that overseas suppliers most often lack.

Documents for metal and scrap into Korea

  • Certificate of analysis per heat or lot, from the producer, with the analysis method stated
  • Producer's quality system certification
  • Certificate of origin
  • Packing list with bundle or bale identification tied to the analysis
  • For scrap: sorting and processing description, radioactivity screening record, and moisture declaration
  • For scrap: confirmation of Korean import classification and any permit the buyer's importer requires for the grade, confirmed per shipment before loading
  • Commercial invoice with the pricing basis (LME reference period and premium) stated

Pricing and payment

LME basis plus premium for metal. Recovery rate sets scrap price. No advance payment against unverified supply.

Primary metal and alloys are priced on an LME basis plus a premium that reflects grade, form, origin, and delivery terms. Scrap is priced as a percentage of the LME reference or at a fixed price per tonne, with the recovery rate from the trial lot setting the level. We quote on FOB, CFR, or CIF terms to Korean ports, with Incheon and Busan the usual destinations.

Payment for primary metal and scrap in international trade is by letter of credit at sight or by telegraphic transfer against documents (documents against payment). We do not request advance payment against unverified supply, and we advise Korean buyers not to pay it to anyone. Intermediaries asking for deposits before documents is the most common pattern in aluminum trading fraud, and the Korean industry has seen it.

Frequently asked questions

Do you hold stock in Korea?

No. Every lot is sourced to order. For buyers who need call-off availability, we structure the supply schedule with the source rather than warehousing in Korea.

Can you supply primary aluminum with a low-carbon certificate?

Low-carbon primary aluminum, produced with hydro or other renewable power and certified by the producer, is available from a limited number of smelters. Korean producers exporting to the EU are beginning to ask for it because it lowers the embedded emissions reported under CBAM. Availability and premium are confirmed per inquiry.

What scrap grades do you supply?

Clean industrial process scrap and segregated alloy scrap by ISRI grade (ReMA Scrap Specifications Circular), as sourced to the buyer's furnace requirements. State the grade and the target alloy in the inquiry.

How long does qualification take?

From specification review to approval, typically one to three months, with the trial lot's shipping time the largest component.

Can you supply to foundries as well as mills?

Yes. Foundries buy primary ingot, secondary alloy ingot, master alloys, and scrap; the qualification sequence is the same.

Have a specification or a sourcing question? Tell us the product, alloy, quantity, and direction.

Discuss your requirement